Header Wallpaper

THE PENDULUM JAR: how to build a pendulum isolated from everything

Avatarչ∂αяквℓσω5 min to read

Hi everyone! Let me explain how I built my "pendulum jar", a tool to figure out

whether a pendulum really moves on its own (questions to entities,

telekinesis, etc.) or whether it's just the fault of air, vibrations, humidity or static

electricity, temperature changes. The idea is simple: isolate the pendulum from all the "normal" causes, so

that if it moves anyway, at least we know it's interesting.

It's cheap and can be done in an afternoon (plus a few days of waiting for the glue).

--- WHAT YOU NEED ---

  • Glass jar with a screw-on lid, 300-400 ml (mine was a bean jar). Inner diameter about 7.5 cm, height about 9 cm.

  • Fluorocarbon fishing line, 0.20 mm thick. Better than nylon and cotton: they absorb almost no moisture and pick up little static. (Dyneema 0.10 mm works too.)

  • Drilled copper sphere, 12 mm diameter, about 8 g. Not too light: the lighter it is, the more it reacts to everything and you can no longer tell what moved it. Avoid steel and iron: they react to the magnetic fields of phones and speakers.

  • An aluminum eyelet or washer, for attaching it to the lid.

  • Two-part epoxy. NOT cyanoacrylate: its vapors settle on the glass.

  • A printed paper disc, 6 cm in diameter, with marks every 5 degrees and circles every 5 mm: it's used to measure how much the pendulum moves, instead of saying "it looks like it moved". (It's also a type of radiant extremely useful for divination with entities)

  • For the base: foam rubber (3 layers of about 1 cm), hot glue, clear silicone. If you can, add a marble or granite tile (30x30 cm, about 5 kg) on top: more mass on a soft support filters slow vibrations better.

  • A silica gel packet (5 g) and some parafilm (or Teflon tape).

  • A digital hygrometer + thermometer to keep in the room.

  • A smartphone on a tripod for filming.

--- HOW TO BUILD IT ---

  1. Wash the jar with bleach, rinse with distilled water and dry it well.

  2. Glue the eyelet to the center of the lid with the epoxy. Let it harden for 48 hours with the lid open, so the vapors escape.

  3. Tie the line to the eyelet and to the sphere (double knot + a drop of epoxy). Line length: 70 mm. The sphere should stay about 8 mm from the bottom, without touching anything.

  4. Glue the disc to the bottom, centered under the sphere.

  5. Put the silica gel packet inside, close the lid and seal the edge with the parafilm.

  6. Make the base: three layers of foam rubber, hot glue, clear silicone to close it off. Then place the tile on top.

  7. Put the jar on the base and leave it for 24-48 hours to rest, so the internal humidity settles. The pendulum has a period of about half a second, so if you see much slower oscillations or slow "strange" movements, that's a whole other story.

--- WHERE AND HOW TO USE IT ---

  • A room at a stable temperature, around 20 degrees C° / 68 F°, away from windows, sun, lamps, radiators and the refrigerator. Temperature gradients matter more than the absolute value: the heat of your body nearby is enough to create currents inside the jar.

  • Humidity: what matters is stability and the fact that it doesn't change during the test, more than a precise value.

  • Better on the ground floor, on a sturdy table near a load-bearing wall.

  • Speak in a low voice and, if you can, from a couple of meters away. Even better: film with the phone and don't stay close.

  • Static electricity: clean the glass with an antistatic cloth and don't wear synthetic sweaters near the jar.

  • Phone and other devices: keep magnets and the actual smartphone away.

--- BEFORE BELIEVING ANYTHING ---

This is the most important part, so do it:

1. The known-disturbances test. Try tapping on the table, walking nearby, bringing a rubbed balloon close, generating a bit of heat with a lamp, talking. Write down how much the pendulum moves in each case.

That way, when you see a movement, you know what might have caused it.

2. The nothing test. Leave the jar alone, in an empty room, for a few hours (even overnight), filming. This is your "baseline": the movement that exists even without questions.

3. Only then ask the questions, and compare. If the movement doesn't clearly exceed the baseline, there's nothing to discuss.

4. If the pendulum answers "yes/no", decide BEFORE what each movement means (e.g. back-and-forth = yes, left-right = no), and run many trials with questions whose answers you don't know. If you don't, our brain sees what it wants to see. (Or instead of yes and no you can still use the letters of the radiant for complex answers).

--- THE LIMITS (so I'm not telling you stories) ---

  • The jar is not under vacuum, so some tiny internal air currents can't be completely ruled out.

  • I haven't guaranteed isolation from very low-frequency vibrations: to really know, you need an accelerometer (a smartphone with the phyphox app, placed on the base, is enough).

  • You are also a source of disturbance: breath, heat, vibrations.

  • If the pendulum moves and you can't find the cause, it means you haven't found the cause yet, not that it's paranormal. It can still be interesting, but it should be replicated.

This can be useful for extremely interesting experiments, such as divination with entities, eliminating almost every kind of interference and guaranteeing a much more effective validation than the pendulum alone with the classic method; it can be useful if you want to experiment with telekinesis and you want to be sure that it's your own aura causing the effect.

next useful links:

No replies found